
كفاءة ثنائي الليزر شبه الموصلSemiconductor Laser Diode Efficiency
سجّل قدرة الخرج P مقابل التيار I من الصفر إلى 40 mA. تعيّن الأداة تيار العتبة Ith وميل الجزء الخطي dP/dI، ثم الكفاءة الكمية التفاضلية ηext = (q/hν) × slope، مع عدم اليقين وخطوات الحل.Record the output power P against the current I from zero to 40 mA. The tool finds the threshold current Ith and the slope dP/dI of the linear part, then the differential quantum efficiency ηext = (q/hν) × slope, with the uncertainty and the solution steps.
الهدف والأجهزةObjective and apparatus
- التعرف على الخصائص المميزة لثنائيات الليزر شبه الموصلة.
- تعيين كفاءة ثنائي الليزر شبه الموصل.
- To learn the distinctive characteristics of semiconductor laser diodes.
- To find the efficiency of a semiconductor laser diode.
- ثنائي ليزر شبه موصل
- مقياس قدرة ليزر
- مصدر جهد مستمر
- أميتر
- مقاومة صغيرة (للحماية) ومقاومة متغيرة
- Semiconductor laser diode
- Laser power meter
- DC voltage source
- Ammeter
- Small (protective) resistor and a variable resistor
الأساس النظريTheory
الكفاءة الكمية التفاضلية ηext هي عدد الفوتونات الخارجة الإضافية لكل إلكترون إضافي يُحقن في الثنائي: نسبة التغير في عدد الفوتونات في الثانية ΔP/hν إلى التغير في عدد الإلكترونات في الثانية ΔI/q. وهي ثابتة تقريباً عند العتبة وفوقها. وتُعيَّن من كفاءة الميل، وهي ميل منحنى قدرة الخرج مقابل التيار فوق العتبة، ووحدتها W/A أو mW/mA، وتُكتب أحياناً في مواصفات ثنائي الليزر.
The differential quantum efficiency ηext is the number of extra photons emitted per extra electron injected into the diode: the ratio of the change in the number of photons per second ΔP/hν to the change in the number of electrons per second ΔI/q. It is roughly constant at and above the threshold. It is found from the slope efficiency, the slope of the output power against current above the threshold, whose unit is W/A or mW/mA and which is sometimes written in the specifications of the laser diode.
تحت تيار العتبة يخرج من الثنائي ضوء ضعيف جداً من الانبعاث التلقائي. وفوق العتبة تزيد قدرة الخرج خطياً مع التيار (الشكل 1):
Below the threshold current very little light, from spontaneous emission, leaves the diode. Above the threshold the output power increases linearly with the current (figure 1):
حيث q شحنة الإلكترون وhν طاقة فوتون الليزر، وهي تساوي تقريباً فجوة الطاقة:
where q is the electron charge and hν the photon energy of the laser, which is almost equal to the band-gap energy:
حيث h ثابت بلانك وc سرعة الضوء وλ الطول الموجي لليزر. ويُعيَّن تيار العتبة Ith من منحنى القدرة مقابل التيار: هو التيار الذي يبدأ عنده الجزء الخطي الحاد، أي تلاقي خطه مع خط الانبعاث التلقائي. ثم تُحسب الكفاءة من ميل P مقابل (I − Ith):
where h is Planck’s constant, c the speed of light and λ the wavelength of the laser. The threshold current Ith is found from the power-current curve: it is the current where the steep linear part begins, that is, where its line meets the spontaneous-emission line. The efficiency is then computed from the slope of P against (I − Ith):
الكفاءة التفاضلية ηext لا تساوي كفاءة تحويل القدرة الكلية P/(IV)، ولا الكفاءة الكمية الكلية qP/(hνI) التي تحسب كل التيار بما فيه تيار العتبة. وقد ينحني المنحنى قليلاً عند التيارات العالية بسبب تسخن الوصلة، لذلك يُقاس بسرعة.
The differential efficiency ηext is not the total power-conversion efficiency P/(IV), nor the total quantum efficiency qP/(hνI), which counts all the current including the threshold current. The curve may bend slightly at high currents because the junction heats up, so the measurement is done quickly.
خطوات التجربةProcedure
ثنائي الليزر شديد الحساسية للكهرباء الساكنة وللتيار الزائد، فلا تتجاوز ظروف التشغيل المسموح بها. واعمل بسرعة لتقليل أثر تسخن الثنائي.
The laser diode is very sensitive to static electricity and to excess current, so do not exceed the stated operating conditions. Work quickly to reduce the effect of the diode heating up.
- صِل مكونات الدائرة كما في الشكل 2، وانتبه لقطبية ثنائي الليزر.
- ضع مقياس القدرة أقرب ما يمكن إلى ثنائي الليزر وغطّهما بقماش أسود، ثم صفّر المقياس والليزر مطفأ. شغّل المصدر وقِس قدرة الخرج بخطوات 1 mA من 0 إلى 40 mA:
- ابدأ والمقاومة المتغيرة عند أكبر قيمة، وسجّل قراءتي الأميتر ومقياس القدرة في الجدول 1.
- قلّل المقاومة المتغيرة تدريجياً، وسجّل القراءتين عند كل خطوة.
- ارسم قدرة الخرج P على المحور الرأسي مقابل التيار I على الأفقي.
- عيّن من المنحنى تيار العتبة Ith.
- ارسم P مقابل الفرق (I − Ith) وعيّن الميل.
- احسب كفاءة ثنائي الليزر ηext من المعادلة (3).
- Connect the components of the circuit as in figure 2, taking care of the polarity of the laser diode.
- Place the power meter as close as possible to the laser diode and cover both with a black cloth, then zero the meter with the laser off. Turn on the supply and measure the output power in 1 mA steps from 0 to 40 mA:
- Start with the variable resistor at its largest value and record the ammeter and power-meter readings in table 1.
- Decrease the variable resistor gradually and record both readings at each step.
- Plot the output power P on the y-axis against the current I on the x-axis.
- From the curve, find the threshold current Ith.
- Plot P against the difference (I − Ith) and find the slope.
- Calculate the laser diode efficiency ηext from equation (3).
الدليل يكتب λ = 532 nm للأخضر، لكن الليزر الأخضر 532 nm ليس ثنائياً يُشع مباشرة، بل ثنائي أشعة تحت حمراء (808 nm) يضخ بلورة تضاعف التردد. فضع في خانة الطول الموجي طول موجة ثنائيك الفعلي (مثلاً 650 nm للأحمر).
The manual gives λ = 532 nm for green, but a green 532 nm laser is not a directly emitting diode: it is an infrared (808 nm) diode pumping a frequency-doubling crystal. So enter in the wavelength field the wavelength of your actual diode (for example 650 nm for red).
المحاكاة التفاعليةInteractive simulation
صفّر مقياس القدرة والمصدر مطفأ، ثم شغّل المصدر وحرّك منزلقة المقاومة المتغيرة لتقل مقاومتها ويزيد التيار، واضغط «سجّل القراءة» عند كل خطوة. تيار العتبة وكفاءة الثنائي غير معروضين، والمطلوب تعيينهما.
Zero the power meter with the supply off, then turn the supply on, move the variable-resistor slider to lower its resistance and raise the current, and press “Record reading” at each step. The threshold current and the efficiency of the diode are not shown; finding them is the task.
النموذج: ثنائي ليزر أحمر 650 nm مع مصدر 5.0 V ومقاومة متغيرة من 5000 إلى 50 Ω ومقاومة حماية 10 Ω. يصل إلى مقياس القدرة ضوء خافت من الغرفة حتى يُصفَّر، ويقل الميل قليلاً عند التيارات العالية بسبب التسخن. في القراءة ضجيج صغير. المحاكاة نموذج لا قياس.Model: a red 650 nm laser diode with a 5.0 V supply, a variable resistor from 5000 to 50 Ω and a 10 Ω protective resistor. Faint room light reaches the power meter until it is zeroed, and the slope falls slightly at high currents because of heating. The readings have a small noise. The simulation is a model, not a measurement.
إدخال البياناتData entry
الجدول 1: التيار I بالمللي أمبير وقدرة الخرج P بالمللي واط. العمود الثالث I − Ith يُحسب بعد تعيين تيار العتبة. لا يلزم ترتيب الصفوف.
Table 1: the current I in milliamperes and the output power P in milliwatts. The third column I − Ith is computed once the threshold current is found. The rows need not be in order.
| رقمNo. | I (mA) | P (mW) | I − Ith (mA) |
|---|
البيانات الحالية توضيحية من نموذج المحاكاة: التيار من 0 إلى 40 mA بخطوة 1 mA بعد تصفير مقياس القدرة، مع ضجيج صغير؛ وليست قياساً.Current data are illustrative, from the simulation model: currents from 0 to 40 mA in 1 mA steps after zeroing the power meter, with a small noise; not a measurement.
لصق بيانات أو تحميل ملف CSVPaste data or load a CSV file
كل سطر: التيار I (mA) ثم القدرة P (mW)، مفصولين بفاصلة أو مسافة.
Each line: the current I (mA) then the power P (mW), separated by a comma or a space.




