
منحنى التيار والجهد لثنائي الليزرI-V Curve of a Laser Diode
غيّر الجهد على ثنائي الليزر بالمقاومة المتغيرة وسجّل التيار والجهد. تعيّن الأداة جهد بدء التوصيل وجهد عتبة الليزر، ثم فجوة الطاقة Eg من امتداد الجزء الخطي، والمقاومة التفاضلية Rs = dV/dI، مع عدم اليقين وخطوات الحل.Change the voltage on the laser diode with the rheostat and record the current and voltage. The tool finds the turn-on voltage and the lasing threshold voltage, then the band-gap energy Eg from the extension of the linear part, and the differential resistance Rs = dV/dI, with the uncertainty and the solution steps.
الهدف والأجهزةObjective and apparatus
- دراسة شكل منحنى التيار والجهد لثنائي الليزر.
- تعيين جهد عتبة الليزر لثنائي الليزر.
- To study the shape of the I-V curve of a laser diode.
- To find the lasing threshold voltage of the laser diode.
- ثنائي ليزر
- مقاومة متغيرة (ريوستات)
- مصدر جهد مستمر
- أميتر
- فولتميتر
- Laser diode
- Rheostat
- DC voltage source
- Ammeter
- Voltmeter
الأساس النظريTheory
معادلة شوكلي للثنائي المثالي (قانون الثنائي) تصف العلاقة بين التيار والجهد في الانحياز الأمامي والعكسي، وكذلك عند انعدام الانحياز:
The Shockley ideal diode equation, also known as the diode law, describes the I-V characteristic of an ideal diode in forward or reverse bias, and also with no bias:
حيث I تيار الثنائي، وIs تيار التشبع العكسي، وVD الجهد على الثنائي، وn معامل الانبعاث (معامل المثالية)، وقيمته بين 1 و2 تقريباً بحسب طريقة التصنيع ومادة شبه الموصل. والجهد الحراري VT خاصية للوصلة:
where I is the diode current, Is the reverse saturation current, VD the voltage across the diode, and n the emission coefficient (ideality factor), between about 1 and 2 depending on the fabrication process and the semiconductor material. The thermal voltage VT is a property of the junction:
حيث k ثابت بولتزمان، وT درجة الحرارة المطلقة، وq مقدار شحنة الإلكترون. ليزر شبه الموصل ثنائي وصلة p-n من مادة ذات فجوة طاقة مباشرة. تحت تيار العتبة يعمل الجهاز مثل الثنائي الباعث للضوء LED، فيخرج ضوءاً على مدى طيفي واسع (20–30 nm). فوق العتبة يضيق الطيف إلى خط ليزر عرضه جزء صغير من النانومتر.
where k is Boltzmann’s constant, T the absolute temperature and q the magnitude of the electron charge. A semiconductor laser is a p-n junction diode made of a direct band-gap semiconductor. Below the threshold current the device works as a light-emitting diode (LED), giving light over a wide spectral range (20–30 nm). Above the threshold the spectrum narrows to a laser line a small fraction of a nanometre wide.
الشكل 1 يبين منحنى التيار والجهد المعتاد لثنائي الليزر. فوق العتبة يثبت جهد الوصلة تقريباً عند قيمة قريبة من Eg/e، لأن كثافة الحاملات في المنطقة الفعالة تثبت عند قيمة العتبة. فيبقى الجهد الزائد على المقاومة المتسلسلة، وتصبح العلاقة خطية:
Figure 1 shows the usual I-V characteristic of a laser diode. Above the threshold the junction voltage stays nearly fixed at a value close to Eg/e, because the carrier density in the active region is pinned at its threshold value. The extra voltage falls on the series resistance, and the relation becomes linear:
حيث Eg طاقة الفجوة، وe شحنة الإلكترون، وRs المقاومة التفاضلية (المقاومة الإضافية أو مقاومة الميل). وحين لا تكون العلاقة خطية تُعرّف المقاومة التفاضلية بأنها مقلوب ميل المنحنى عند قيمة معينة للجهد أو التيار:
where Eg is the band-gap energy, e the electron charge and Rs the differential resistance (also called incremental or slope resistance). When the relation is not linear, the differential resistance is defined as the inverse of the slope of the characteristic at a given voltage or current:
تُعيَّن Eg بمدّ الجزء الخطي فوق العتبة حتى يقطع محور الجهد (I = 0)، فتكون نقطة القطع Eg/e. هذه النقطة ليست جهد العتبة نفسه، فجهد العتبة أكبر منها بمقدار IthRs. والقيمة تقريبية، لأن جهد الوصلة فوق العتبة يساوي طاقة الفوتون مقسومة على e مضافاً إليها فروق صغيرة عند الوصلات غير المتجانسة.
Eg is found by extending the linear part above the threshold until it cuts the voltage axis (I = 0), and the intercept is Eg/e. This intercept is not the threshold voltage itself; the threshold voltage is larger by IthRs. The value is approximate, because the junction voltage above the threshold equals the photon energy divided by e plus small offsets at the heterojunctions.
خطوات التجربةProcedure
- صِل مكونات الدائرة كما في الشكل 2.
- شغّل جهازي القياس الموصولين في الدائرة. غيّر الجهد على ثنائي الليزر ببطء بتحريك منزلق الريوستات من أحد طرفيه (أكبر قيمة) إلى الآخر، وستتغير قراءتا الأميتر والفولتميتر.
- قِس التيار I بدلالة الجهد V بزيادات صغيرة بدءاً من 0 V.
- ارسم من البيانات المسجلة منحنى التيار مقابل الجهد.
- أوجد من الرسم:
- النقطة الأولى التي يتغير عندها الميل فجأة ويبدأ الليزر بالتوهج الخافت (جهد بدء التوصيل).
- النقطة الثانية التي يتغير عندها الميل فجأة ويضيء الليزر بشدة (جهد عتبة الليزر).
- طاقة الفجوة Eg.
- عيّن من المنحنى المقيس المقاومة التفاضلية Rs = dV/dI، وهي مقلوب ميل الخط المستقيم.
- Connect the components of the circuit as shown in figure 2.
- Turn on the two meters connected in the circuit. Slowly change the voltage applied to the laser diode by sliding the rheostat from one end (maximum value) to the other; as you do so, the ammeter and voltmeter readings change.
- Measure the current I as a function of the voltage V in small increments starting at 0 V.
- From the recorded data, draw a graph of the current against the voltage (I-V curve).
- From the graph find:
- The first point where the slope changes abruptly and the laser barely begins to glow (turn-on voltage).
- The second point where the slope changes abruptly and the laser begins to glow very brightly (lasing threshold voltage).
- The band-gap energy Eg.
- Determine from the measured characteristic the differential resistance Rs = dV/dI, which is the inverse of the slope of the straight line.
لا تتجاوز أقصى تيار يسمح به صانع الثنائي، فقد يتلف الثنائي فوق العتبة بقليل، ويجب أن تحتوي الدائرة على مقاومة حماية. وخذ قراءات متقاربة قرب العتبة وفوقها، لأن تحديد الجزء الخطي يحتاج إلى أربع نقاط على الأقل. ولا تنظر إلى شعاع الليزر مباشرة.
Do not exceed the maximum current allowed by the diode maker; the diode can be damaged a little above the threshold, and the circuit must contain a protective resistor. Take closely spaced readings near and above the threshold, because finding the linear part needs at least four points. Do not look into the laser beam.
المحاكاة التفاعليةInteractive simulation
حرّك منزلق الريوستات بالأزرار أو بالمنزلق من 0%، وراقب قراءتي الأميتر والفولتميتر وضوء الثنائي. اضغط «سجّل القراءة» بعد كل خطوة لتنتقل القراءتان إلى الجدول، وقارب الخطوات حين يبدأ التيار بالارتفاع. جهد العتبة وفجوة الطاقة والمقاومة غير معروضة، والمطلوب تعيينها.
Move the rheostat slider with the buttons or the slider from 0%, and watch the ammeter and voltmeter readings and the light of the diode. Press “Record reading” after each step to move the two readings to the table, and use smaller steps once the current starts to rise. The threshold voltage, band gap and resistance are not shown; finding them is the task.
النموذج: ثنائي ليزر أحمر تتبع وصلته معادلة شوكلي تحت العتبة، ويثبت جهدها فوق العتبة، وفيه مقاومة متسلسلة. المصدر 5.0 V مع ريوستات بوصلة مجزّئ جهد ومقاومة حماية. في القراءات خطأ بحدود آخر رقم. المحاكاة نموذج لا قياس.Model: a red laser diode whose junction follows the Shockley equation below the threshold and whose junction voltage is pinned above it, with a series resistance. The source is 5.0 V with a rheostat wired as a voltage divider and a protective resistor. The readings carry an error of about the last digit. The simulation is a model, not a measurement.
إدخال البياناتData entry
الجدول 1: التيار I بالمللي أمبير والجهد V بالفولت لكل قراءة، ويتسع لثلاثين قراءة كما في الدليل. لا يلزم ترتيب الصفوف.
Table 1: the current I in milliamperes and the voltage V in volts for each reading, with room for thirty readings as in the manual. The rows need not be in order.
| رقمNo. | I (mA) | V (V) |
|---|
البيانات الحالية توضيحية من نموذج المحاكاة: ثلاثون قراءة من 0 V حتى أقصى تيار، أكثرها قرب العتبة وفوقها؛ وليست قياساً.Current data are illustrative, from the simulation model: thirty readings from 0 V up to the maximum current, most of them near and above the threshold; not a measurement.




