المعامل الطلابيةعملية 3معامل برنامج الطاقةمعامل برنامج الفيزياءمعمل الموجات والبصريات

توليد موجات موقوفة وتعيين طولها الموجي

Standing Waves on a String and Their Wavelength

الموجات الموقوفة

توليد موجات موقوفة وتعيين طولها الموجيStanding Waves on a String and Their Wavelength

غيّر قوة الشد F حتى تتكوّن على الحبل موجة موقوفة بعدد بطون n، وتحسب الأداة الطول الموجي λ = 2L/n وميل λ² مقابل F، ومنه الكتلة لوحدة الطول μ وكتلة الحبل m مع عدم اليقين وخطوات الحل.Change the tension F until a standing wave with n antinodes forms on the string, and the tool computes the wavelength λ = 2L/n and the slope of λ² against F, then the mass per unit length μ and the string mass m with their uncertainty and the solution steps.

الهدف والأجهزةObjective and apparatus

دراسة الطول الموجي للموجات الموقوفة على الحبل بوصفه دالة في قوة الشد F وعدد البطون n وطول الحبل L، والتحقق من العلاقة بين قوة الشد والطول الموجي:

To study the wavelength of standing waves on a string as a function of the tension F, the number of antinodes n and the string length L, and to verify the relation between tension and wavelength:

$$\lambda=\frac{1}{f}\sqrt{\frac{F}{\mu}}=\frac{1}{f}\sqrt{\frac{F\,L}{m}}$$
  • جهاز ذبذبة الحبل (هزاز بتردد ثابت f مدوّن على الجهاز)
  • حبل أو خيط خفيف
  • حامل رأسي بماسك (a, b في الشكل) يُعلَّق فيه الميزان
  • ميزان زنبركي أو مستشعر لقياس قوة الشد F
  • مسطرة لقياس الطول L
  • String vibrator (fixed frequency f, written on the device)
  • A light string or thread
  • Vertical rod with clamp (a, b in the figure) holding the balance
  • Spring balance or force sensor to measure the tension F
  • Ruler to measure the length L

الأساس النظريTheory

يهز الهزاز طرف الحبل عمودياً على طوله، فتنتشر على الحبل موجة مستعرضة تنعكس عند الطرف الثابت، وتتراكب الموجتان الذاهبة والمنعكسة. سرعة الموجة المستعرضة على حبل مشدود بقوة F وكتلته لوحدة الطول μ = m/L هي:

The vibrator shakes the end of the string perpendicular to its length, so a transverse wave travels along the string, reflects at the fixed end, and the incident and reflected waves superpose. The speed of a transverse wave on a string under tension F with mass per unit length μ = m/L is:

$$v=\sqrt{\frac{F}{\mu}}$$
(1)

الطرفان عقدتان، فلا تتكوّن موجة موقوفة واضحة السعة (رنين) إلا إذا احتوى طول الحبل عدداً صحيحاً من أنصاف الأطوال الموجية؛ وكل نصف طول موجي بطن واحد:

Both ends are nodes, so a standing wave of clear amplitude (resonance) forms only when the string length holds a whole number of half wavelengths; each half wavelength is one antinode:

$$L=n\,\frac{\lambda}{2}\;\;\Rightarrow\;\;\lambda=\frac{2L}{n},\qquad n=1,2,3,\dots$$
(2)

تردد الهزاز f ثابت، وv = fλ؛ فبالتعويض في (1) وتربيع الطرفين:

The vibrator frequency f is fixed and v = fλ; substituting in (1) and squaring:

$$\lambda^{2}=\frac{1}{\mu f^{2}}\,F$$
(3)

أي أن λ² يتناسب طردياً مع F، ورسم λ² مقابل F خط مستقيم يمر بنقطة الأصل ميله:

So λ² is directly proportional to F, and the plot of λ² against F is a straight line through the origin with slope:

$$s=\frac{1}{\mu f^{2}}=\frac{L}{m f^{2}}\;\;\Rightarrow\;\;\mu=\frac{1}{f^{2}s},\quad m=\mu L$$
(4)

الهزاز الكهرومغناطيسي الموصول بتيار متردد 60 Hz يهتز غالباً بتردد 120 Hz (يُجذب مرتين في كل دورة)، والهزاز ذو المغناطيس الدائم بتردد 60 Hz؛ اعتمد المدوّن على جهازك.

An electromagnetic vibrator on 60 Hz mains usually vibrates at 120 Hz (attracted twice per cycle), and one with a permanent magnet at 60 Hz; use the value written on your device.

خطوات التجربةProcedure

  1. ثبّت الحبل بين طرف الهزاز والمسمار عند الحامل، واربط طرفه الآخر بالميزان الزنبركي المعلّق في ماسك الحامل.
  2. قِس طول الحبل L من طرف الهزاز إلى المسمار كما في الشكل، وسجّل تردد الهزاز f.
  3. شغّل الهزاز، ثم غيّر قوة الشد F بتحريك الماسك على الحامل حتى تتكوّن موجة موقوفة ذات بطن واحد وعقدتين عند الطرفين، وسجّل F.
  4. أنقص الشد ببطء وكرّر لتكوين موجات موقوفة بعدد بطون مختلف (2، 3، 4، 5 …)، وسجّل لكل حالة n وF عند أكبر سعة.
  5. احسب الطول الموجي λ = 2L/n ثم λ².
  6. ارسم λ² على محور الصادات مقابل F على محور السينات، واحسب الميل s، ثم μ وm من المعادلة (4).
  1. Fix the string between the vibrator end and the pin at the rod, and tie its other end to the spring balance hung in the rod clamp.
  2. Measure the string length L from the vibrator end to the pin as in the figure, and note the vibrator frequency f.
  3. Switch on the vibrator, then change the tension F by moving the clamp along the rod until a standing wave with one antinode and two nodes at the ends forms, and record F.
  4. Decrease the tension slowly and repeat to form standing waves with different numbers of antinodes (2, 3, 4, 5 …), recording n and F at the largest amplitude in each case.
  5. Compute the wavelength λ = 2L/n and then λ².
  6. Plot λ² on the vertical axis against F on the horizontal axis, find the slope s, then μ and m from equation (4).

الأطوال بالسنتيمتر وقوة الشد بالنيوتن؛ إذا قست L بالمتر فاضربه في 100. اقترب من الرنين ببطء من الجهتين، وسجّل F عند أكبر سعة، وكرّر القراءة واحسب متوسطها.

Lengths are in centimetres and the tension in newtons; if you measured L in metres, multiply by 100. Approach resonance slowly from both sides, record F at the largest amplitude, and repeat the reading and average it.

المحاكاة التفاعليةInteractive simulation

حرّك منزلق قوة الشد (أو اسحب الميزان على الحامل) حتى تكبر سعة الحبل وتظهر بطون واضحة، ثم اضبط بزرّي − و+ على أكبر سعة وسجّل القراءة. تذهب القراءة إلى أول صف فارغ في الجدول. كتلة الحبل في المحاكاة غير معروضة، والمطلوب تعيينها.

Move the tension slider (or drag the balance along the rod) until the string amplitude grows and clear antinodes appear, then fine-tune with the − and + buttons to the largest amplitude and record the reading. It goes to the first empty row of the table. The string mass in the simulation is not shown; finding it is the task.

ضبط دقيقFine adjustment

النموذج: حبل طرفاه عقدتان يُهز أحدهما بسعة صغيرة وتردد ثابت، مع تخميد خفيف؛ سعة البطن تكبر كثيراً حين يقترب 2L/λ من عدد صحيح. الحركة معروضة ببطء لتُرى، والمساحة الفاتحة هي ما تراه العين من الحبل المهتز. المحاكاة نموذج لا قياس.Model: a string with nodes at both ends, one end shaken with a small amplitude at a fixed frequency, with light damping; the antinode amplitude grows strongly when 2L/λ approaches a whole number. The motion is shown slowed down, and the light area is what the eye sees of the vibrating string. The simulation is a model, not a measurement.

إدخال البياناتData entry

عدد البطونAntinodes (n)قوة الشدTension F (N)الطول الموجيWavelength λ (cm)λ² (cm²)
لصق بيانات أو تحميل ملف CSVPaste data or load a CSV file

اظهر المزيد

محمد بن سعد الميلبي

مؤسس مبادرة معامل الفيزياء | مطور حلول رقمية بالذكاء اصطناعي في مجال الفيزياء التعلمية والتحليل العلمي

اترك تعليقاً

لن يتم نشر عنوان بريدك الإلكتروني. الحقول الإلزامية مشار إليها بـ *

زر الذهاب إلى الأعلى